 |
特性
- 高度 performance, low cost
- Supply voltage up to +40VDC
- output current up to 1.5A
- Inaudible 20khz chopping frequency
- TTL compatible and optically isolated input signals
- Automatic idle-current reduction
- Mixed-decay current control for less motor heating
- 7 selectable resolutions up to 12,800 steps/rev
- Microstep resolution can be changed on the fly (optional)
- Suitable for 2-phase and 4-phase stepping motors
- Reverse polarity protection
- Small size: 86x55x20mm
|
Introduction:
M415B is a very small size high performance microstepping driver based on one of the most advanced technologies in the world today. It is suitable for driving any 2-phase and 4-phase hybrid stepping motors. By using advanced bipolar constant-current chopping technique, it can output more speed and power from the same motor, compared with traditional technologies such as L/R drivers. |
应用s:
Suitable for a wide range of stepping motors of size Nema 16, 17 and 23, and usable for various kinds of machines, such as X-Y tables, labeling machines, laser cutters, engraving machines, and pick-place devices. Extremely suitable for applications which expected to be low vibration, high speed and high precision.
|
| Electric 参数 (Tj=25o) |
|
M415B |
| Supply voltage |
+18 to 40 VDC |
| Typical Supply voltage |
+24 --- +36 VDC |
| Output current peak value |
0.1 to 1.5 A (adjustable) |
| Microstep Resolution (7 choices) |
1,2, 4, 8, 16, 32, 64. |
|
| Mechanical 参数 (单位: mm, 1 inch=25.4 mm) |
 |
| Pin Assignment and 描述 |
| Control Signal Connector P1 pins |
| Pin No. |
Signal |
描述 |
| 1 |
PUL |
Pulse signal: effective for each upward-rising edge, motor runs a microstep when the pulse changes from low to high |
| 2 |
DIR |
Direction signal: used to change the motor rotating direction. |
| 3 |
OPTO |
Opto-coupler power supply, +5V typical. |
| 4 |
ENA |
Enable signal: Enable or disable the driver, low level disabled |
|
| 功率 connector P2 pins |
| Pin Funtion |
Details |
| Gnd |
DC power ground |
| +V |
DC power positive, typical value 24V |
| Phase A |
电机 coil A (leads A+ and A-) |
| Phase B |
电机 coil B (leads B+ and B-) |
|
| Microstep Resolution Selection |
| Microstep resolution is set by SW4, 5, 6 of the DIP switch or MS0, MS1, MS2 of the DIP switch as shown in the following table: |
| Microstep |
usteps/rev.( 1.8°/rev) |
SW4/MS0 |
SW5/MS1 |
SW6/MS2 |
| 1 |
200 |
ON |
ON |
ON |
| 2 |
400 |
OFF |
ON |
ON |
| 4 |
800 |
ON |
OFF |
ON |
| 8 |
1600 |
OFF |
OFF |
ON |
| 16 |
3200 |
ON |
ON |
OFF |
| 32 |
6400 |
OFF |
ON |
OFF |
| 64 |
12800 |
ON |
OFF |
OFF |
| *Microstep change on the fly |
Set by control signal from P1 |
OFF |
OFF |
OFF |
|
| 电流 Setting |
| 电流 ( peak) |
SW1 |
SW2 |
SW3 |
| 0.21A |
OFF |
ON |
ON |
| 0.42A |
ON |
OFF |
ON |
| 0.63A |
OFF |
OFF |
ON |
| 0.84A |
ON |
ON |
OFF |
| 1.05A |
OFF |
ON |
OFF |
| 1.26A |
ON |
OFF |
OFF |
| 1.5A |
OFF |
OFF |
OFF |
|
| Typical Connections |
 |
主页
